RESEARCHER PROFILE

Kai Treutler

← Back to Clausthal University of Technology

K

Clausthal University of Technology

Welding Techniques and Residual StressesAdditive Manufacturing Materials and ProcessesAdvanced Welding Techniques AnalysisMetal Alloys Wear and PropertiesAdvanced machining processes and optimization

Kai Treutler works in Welding Techniques and Residual Stresses, Additive Manufacturing Materials and Processes, Advanced Welding Techniques Analysis, Metal Alloys Wear and Properties, Advanced machining processes and optimization. Recorded institutional associations include Clausthal University of Technology.

75Publications
842Citations
14H-index

Inclusion identifies researchers whose recorded research contributions may inform their university’s understanding of its research community. It does not rank individual research quality or establish current employment.

Selected research works

Up to 100 highly cited works; DOI links open the original research. Counts reflect the collected record, not real-time citation totals.

  1. The Current State of Research of Wire Arc Additive Manufacturing (WAAM): A Review

    2021 · 293 citations
  2. Monotonic and Fatigue Properties of Steel Material Manufactured by Wire Arc Additive Manufacturing

    2020 · 39 citations
  3. Surface finishing of hard-to-machine cladding alloys for highly stressed components

    2021 · 37 citations
  4. Multi-Material Design in Welding Arc Additive Manufacturing

    2019 · 32 citations
  5. Simulation-based process parameter optimization for wire arc additive manufacturing

    2024 · 30 citations
  6. Real-time measurement of temperature and volume of the weld pool in wire-arc additive manufacturing

    2021 · 28 citations
  7. Multi-material design in additive manufacturing—feasibility validation

    2020 · 22 citations
  8. Wire and Arc Additive Manufacturing of a CoCrFeMoNiV Complex Concentrated Alloy Using Metal-Cored Wire—Process, Properties, and Wear Resistance

    2022 · 19 citations
  9. Properties oriented WAAM—microstructural and geometrical control in WAAM of low-alloy steel

    2023 · 17 citations
  10. Influencing the arc and the mechanical properties of the weld metal in GMA-welding processes by additive elements on the wire electrode surface

    2016 · 16 citations
  11. Optimisation of surface residual stresses using ultrasonic-assisted milling for wire-arc additive manufactured Ni alloy components

    2023 · 15 citations
  12. High geometric fidelity through closed-loop control of the weld pool size in gas metal arc welding based direct energy deposition

    2023 · 15 citations
  13. In situ chemical analysis of duplex stainless steel weld by laser induced breakdown spectroscopy

    2024 · 15 citations
  14. On the Microstructure Development under Cyclic Temperature Conditions during WAAM of Microalloyed Steels

    2022 · 14 citations
  15. Alloy modification for additive manufactured Ni alloy components—part I: effect on microstructure and hardness of Invar alloy

    2023 · 14 citations
  16. Targeted influence on the weld strength of high-strength fine-grain structural steels in the GMA welding process through functionalized weld material surfaces

    2019 · 13 citations
  17. Assessing ferrite content in duplex stainless weld metal: WRC ‘92 predictions vs. practical measurements

    2024 · 13 citations
  18. Modification of Co–Cr alloys to optimize additively welded microstructures and subsequent surface finishing

    2022 · 12 citations
  19. Echtzeittemperaturmessung bei additivem Lichtbogenschweißen / Real-time temperature measurement at wire arc additive welding

    2019 · 10 citations
  20. Characterization of Influences of Steel-Aluminum Dissimilar Joints with Intermediate Zinc Layer

    2020 · 10 citations
  21. Re-Melting Behaviour and Wear Resistance of Vanadium Carbide Precipitating Cr27.5Co14Fe22Mo22Ni11.65V2.85 High Entropy Alloy

    2021 · 10 citations
  22. Micromagnetic Properties of Powder Metallurgically Produced Al Composites as a Fundamental Study for Additive Manufacturing

    2022 · 10 citations
  23. New Developments in the Field of Production and Application of Multi‐Material Wire Arc Additive Manufacturing Components: A Review

    2025 · 10 citations
  24. Impact of notch geometry on dynamic strength of materials

    2019 · 7 citations
  25. Usage of Ti-surface-modified filler material to increase the joint strength of High-Strength Low Alloyed (HSLA) steels under different load types

    2020 · 7 citations

← Return to the university profile