RESEARCHER PROFILE

Nikhil Ranjan Dhar

← Back to Bangladesh University of Engineering and Technology

N

Bangladesh University of Engineering and Technology

Advanced machining processes and optimizationAdvanced Machining and Optimization TechniquesEngineering Technology and MethodologiesAdvanced Surface Polishing TechniquesLubricants and Their Additives

Nikhil Ranjan Dhar works in Advanced machining processes and optimization, Advanced Machining and Optimization Techniques, Engineering Technology and Methodologies, Advanced Surface Polishing Techniques, Lubricants and Their Additives. Recorded institutional associations include Bangladesh University of Engineering and Technology.

101Publications
5,449Citations
34H-index

Inclusion identifies researchers whose recorded research contributions may inform their university’s understanding of its research community. It does not rank individual research quality or establish current employment.

Selected research works

Up to 100 highly cited works; DOI links open the original research. Counts reflect the collected record, not real-time citation totals.

  1. Effect of minimum quantity lubrication (MQL) on tool wear and surface roughness in turning AISI-4340 steel

    2005 · 551 citations
  2. Effects of minimum quantity lubrication on turning AISI 9310 alloy steel using vegetable oil-based cutting fluid

    2009 · 489 citations
  3. The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel

    2005 · 350 citations
  4. An experimental investigation on effect of minimum quantity lubrication in machining AISI 1040 steel

    2006 · 287 citations
  5. Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition

    2006 · 253 citations
  6. Multi-objective optimization and life cycle assessment of eco-friendly cryogenic N2 assisted turning of Ti-6Al-4V

    2018 · 218 citations
  7. Prediction of surface roughness in hard turning under high pressure coolant using Artificial Neural Network

    2016 · 207 citations
  8. Optimization of surface roughness and cutting temperature in high-pressure coolant-assisted hard turning using Taguchi method

    2016 · 200 citations
  9. Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI 1060 steel

    2001 · 180 citations
  10. Performance evaluation of minimum quantity lubrication by vegetable oil in terms of cutting force, cutting zone temperature, tool wear, job dimension and surface finish in turning AISI-1060 steel

    2006 · 157 citations
  11. The influence of cryogenic cooling on tool wear, dimensional accuracy and surface finish in turning AISI 1040 and E4340C steels

    2001 · 138 citations
  12. Optimization of MQL flow rate for minimum cutting force and surface roughness in end milling of hardened steel (HRC 40)

    2016 · 133 citations
  13. Response surface and neural network based predictive models of cutting temperature in hard turning

    2016 · 124 citations
  14. Study of surface roughness and cutting forces using ANN, RSM, and ANOVA in turning of Ti-6Al-4V under cryogenic jets applied at flank and rake faces of coated WC tool

    2017 · 119 citations
  15. Effects of duplex jets high-pressure coolant on machining temperature and machinability of Ti-6Al-4V superalloy

    2017 · 116 citations
  16. Machining of AISI 4140 steel under cryogenic cooling—tool wear, surface roughness and dimensional deviation

    2002 · 111 citations
  17. Role of Cryogenic Cooling on Cutting Temperature in Turning Steel

    2001 · 97 citations
  18. Effect of time-controlled MQL pulsing on surface roughness in hard turning by statistical analysis and artificial neural network

    2017 · 97 citations
  19. Mono-objective and multi-objective optimization of performance parameters in high pressure coolant assisted turning of Ti-6Al-4V

    2016 · 83 citations
  20. High-pressure coolant on flank and rake surfaces of tool in turning of Ti-6Al-4V: investigations on surface roughness and tool wear

    2016 · 83 citations
  21. Prediction and optimization by using SVR, RSM and GA in hard turning of tempered AISI 1060 steel under effective cooling condition

    2017 · 79 citations
  22. Effect of Minimum Quantity Lubrication (MQL) on Tool Wear, Surface Roughness and Dimensional Deviation in Turning AISI-4340 Steel

    2010 · 74 citations
  23. Effects of internal cooling by cryogenic on the machinability of hardened steel

    2016 · 74 citations
  24. Influence of single and dual cryogenic jets on machinability characteristics in turning of Ti-6Al-4V

    2017 · 72 citations
  25. Design and evaluation of an embedded double jet nozzle for MQL delivery intending machinability improvement in turning operation

    2019 · 70 citations

← Return to the university profile